Last Updated 05 Oct 2022

Essay about Introduction to Forensic Science

Words 605 (2 pages)

1. What is the NIBIN? NIBIN is the National Integrated Ballistic Identification Network that was created by the FBI and the ATF in 1999.

2. What is rifling? What two types of markings does this produce? Rifling is when each gun is given spiral grooves by the manufacturer. The spiral grooves are cut into the barrel of a gun in order to make a bullet spin as it is fired. Rifling produces grooves and lands.

3. What is a distance determination? How is this done? A distance determination is the process of estimating the distance between where a shot is fired and its target. This is often done by looking at the patterns of powder residue and the shot pattern.

Order custom essay Essay about Introduction to Forensic Science with free plagiarism report


4. What is the Greiss Test? The Greiss Test uses chemicals to develop gunpowder residue patterns, particularly around bullet holes.

5. When a bullet is retrieved, how is it marked for identification purposes? What should be avoided? Once a bullet has been retrieved, it is usually marked with the investigator's initials, often at the tip or base of the bullet. The sides of the bullet should not be marked. Care has to be taken that this mark does not cover or obscure any striations or markings on the bullet. Critical Thinking Questions

1. If you found a firearm at a crime scene, what steps would you take in order to transport the weapon to the lab? First, I would make a note about the position of the gun’s safety and hammer. Then, I would need to unload the gun before it is transported or handled in analysis. Finally, I would take each round from the firearm and place it in a separate envelope.

2. Why do you think it might be useful to know the distance between a gun fired and its target? It would be useful to know the distance because if you know the distance, you might be able to find more clues as to who committed the crime based on where they shot the victim.

3. If you were in charge of retrieving bullets at a crime scene, what steps would you take to retrieve a bullet and take it to the crime lab? If I were in charge of retrieving bullets at a crime scene I would first have to find a way to remove the bullet out while preserving any possible markings on the bullet. Then the bullets can be placed into a marked container for identification purposes. Then to transport the bullet to the crime laboratory, I’d wrap the bullet in tissue paper and placed in an envelope or pillbox. I would have to be careful with the handling and packaging of the bullet, because I would have to be careful to preserve any trace evidence that might be present on the bullet.

4. What are some of the challenges in analyzing tool marks? Some of the challenges in analyzing tool marks is it is difficult to duplicate the mark left by tools through tests in the laboratory and tool marks may not always give individual characteristics.

5. What is the Doppler Effect? How can the Doppler Effect be useful for a forensic investigation involving a shooting? It is important for a forensic scientist to determine the distance from a gun to a shooter because in some cases a defendant accused of murder may say that the shooting happened in self-defense. Figuring out the distance between the two individuals may give an indication of whether the defendant is telling the truth or not. Similarly, knowing an approximate distance of a shot can help forensic scientists determine if a death was a suicide or a homicide made to look like a suicide.

Essay about Introduction to Forensic Science essay

Related Questions

on Essay about Introduction to Forensic Science

When A Bullet Is Retrieved How Is It Marked For Identification Purposes?
A bullet is usually marked for identification purposes when it is retrieved from a crime scene. The markings on the bullet can help to identify the type of gun that was used, the caliber of the gun, and the distance the bullet was fired from.
What Is Rifling What Two Types Of Markings Does This Produce?
Rifling is a process of putting spiral grooves in the barrel of a gun. These grooves give the bullet a spin as it leaves the barrel. The spin makes the bullet more stable in flight, giving it a straighter, more accurate path. There are two types of markings that rifling produces: land and groove. Land marks are the high points between the spiral grooves. They are raised up above the level of the grooves and are smooth. The groove marks are the low points between the spiral grooves. They are sunken below the level of the lands and are also smooth.
What Are Some Challenges In Analyzing Tool Marks?
There are a few different challenges that can present themselves when analyzing tool marks. One challenge is that the marks left behind by a tool can be very small and hard to see. This can make it difficult to identify the tool that was used to create the marks. Another challenge is that the marks can be easily damaged or destroyed, making them difficult to preserve and study. Finally, the marks can be left by a variety of different tools, making it hard to narrow down the field of possible suspects.
Why Is It Useful To Know The Distance Between A Gun Fired And Its Target?
There are a few reasons why it is useful to know the distance between a gun fired and its target. For one, it can help to determine how much the bullet will drop over the course of its flight. This is important information for long-range shooting, as a well-placed shot can easily be ruined by a bullet that drops too much before it reaches the target. Additionally, knowing the distance can help to determine the amount of energy the bullet will have when it reaches the target. This is important because a bullet with too much energy can cause extensive damage to the target, while a bullet with too little energy may not penetrate the target at all. Finally, knowing the distance can help to ensure that the gun is properly sighted-in. If the gun is not properly sighted-in, the bullet will not hit the target where the shooter is aiming.
What Uses Chemicals To Develop Gunpowder Residue Patterns?
There are many ways to develop gunpowder residue patterns, but one of the most common is to use chemicals. Chemicals can be used to develop latent prints, which are invisible fingerprints that can be left on surfaces by the oils in our skin. They can also be used to develop bloodstains, which can help investigators determine the path of a bullet or where a body was moved.

This essay was written by a fellow student. You can use it as an example when writing your own essay or use it as a source, but you need cite it.

Get professional help and free up your time for more important courses

Starting from 3 hours delivery 450+ experts on 30 subjects
get essay help 124  experts online

Did you know that we have over 70,000 essays on 3,000 topics in our database?

Cite this page

Explore how the human body functions as one unit in harmony in order to life

Essay about Introduction to Forensic Science. (2016, Aug 11). Retrieved from

Don't let plagiarism ruin your grade

Run a free check or have your essay done for you

We use cookies to give you the best experience possible. By continuing we’ll assume you’re on board with our cookie policy

Save time and let our verified experts help you.

Hire writer