2×2 Switch Simulation in Matlaab

Category: Scientific Method
Last Updated: 26 Jan 2021
Pages: 3 Views: 158

2x2 Packet Switch Simulation

Contents Page

    Order custom essay 2×2 Switch Simulation in Matlaab with free plagiarism report

    feat icon 450+ experts on 30 subjects feat icon Starting from 3 hours delivery
    Get Essay Help
  1. Aim 1. 2 Methodology
  2. Objectives
  3. Background
  4. Performance Evaluation
  5. Measurement
  6. Analysis/Simulation
  7. Packet Switched Networks
  8. Introduction
  9. Theory
  10. Queuing Theory
  11. Queuing Model
  12. Concept of a queuing model
  13. Queuing theory notation
  14. The M/M/1 Queue
  15. The M/D/1 Queue
  16. Switching
  17. Switching Concept
  18. Internal Link Blocking
  19. Output Port Contention
  20. Head Of Line Blocking
  21. Time Between Arrivals
  22. Counting Arrivals
  23. The Queuing Behaviour Of Packets In Output Buffers
  24. Calculating The State Probability Distribution
  25. Analytical /Simulation Results
  26. 2x2 Switch
  27. Analytical Results
  28. Simulation Results
  29. 4x4 Switch
  30. Analytical Results
  31. Simulation Results
  32. 8x8 Switch
  33. Analytical Results
  34. Simulation Results
  35. 16x16 Switch
  36. Analytical Results
  37. Simulation Results
  38. Conclusion
  39. Project Management
  40. Risk Analysis
  41. Gant Chart
  42. References

Interim report 2x2

Packet Switch Simulation Using Matlab

Test out a simulation on fundamental 2x2 switch element. Then expand it. Learn about Matlab. Learn about simulation.  Build a simple test model and try it. Build a 2x2 element in Matlab.  Simulate any new results required? Write a report. When networks are designed, the goal of the performance evaluation is to determine the best effect of the equipment sed. Methods for performance evaluation are measurement techniques, analysis, and simulation.  Measurement For measurement methods real networks is used for experimentation. The advantage of direct measurement of network performance is that no detail of network operation is excluded but experience hard to test performance limits. Customers won’t like it when you crash the system.

Analysis/ Simulation

In comparing analysis and simulation, the main factors to consider are the accuracy of results, the time to produce results, and the overall cost of using the method. The advantage of analytical solutions is that they are quite a good fit for reality and produces results quickly. However, assumptions required to define equations and parameters and they can be very complex. Simulation provides system representation to the required precision. However, simulation can be time and cost demands. In a packet-switched network, all nodes interconnected by directed links. Packets are routed independently. Packets enter the network at a specific node where they may be queued in a buffer to wait for an outgoing channel to become free. This continued in a hop by hop manner until the packets finally arrive at their destination. Packets may arrive at the same destination by taking different routes. That increases the efficiency of transmission resources. Also queued packets in the buffer will cause a variable delay and throughput, depending on traffic load. Basic network is shown in figure 1.

Figure 1: Packet Switched Network 3.

Introduction

Contention in a switch affects the performance of a switch. To prevent this some switching techniques are developed. One of the most common switching techniques is the one with an output-buffered switch. In this report, the queuing process of performance evaluation, for such a switch is done analytically first than simulation analysis is done using Matlab. At the end of the report comparison of the two results is done.

Theory

Queuing Theory Analysis of the queuing process is basic and essential part of the performance evaluation. Because queues are formed in a network when there is a high demand for limited resources.  Queuing Model Packets arrive at a queuing system to be served for a certain time. If service is not immediately available they wait for service in a storage area (buffer). After a certain length of time, they are served and leave the system. The basic queuing system is shown in the figure.

Cite this Page

2×2 Switch Simulation in Matlaab. (2017, Dec 07). Retrieved from https://phdessay.com/2x2-switch-simulation-in-matlaab/

Don't let plagiarism ruin your grade

Run a free check or have your essay done for you

plagiarism ruin image

We use cookies to give you the best experience possible. By continuing we’ll assume you’re on board with our cookie policy

Save time and let our verified experts help you.

Hire writer