Chapter 16 Milady Denham Springs Beauty College Rias class

Foundation
A good haircut serves as the________ for attractive hairstyles and other services performed in the salon
Beveling
A technique of using diagonal lines by cutting hair ends with a slight increase or decrease in length is called:
Blunt cutting
Cutting the hair straight across the Strand where the lengths of the hair all come to one hanging level, forming a weight line, is known as:
Notching or Point cutting
Cutting with the points of the shears to create texture in the hair is known as:
Graduated
When they graduated shape, or wedge, has a stacked area around the exterior and his cut at low to medium elevations, it is known as:
Guide
The section of hair that determines the length the hair will be cut is called the:
We will write a custom essay sample on
Any topic specifically for you
For only $13.90/page
Order Now
Tension
How tightly the hair is pulled when cutting is referred to as:
Weight line
The level at which a blunt cut Falls is called the:
Uneven
If the hair is cut while parts are partly wet and parts are partly dry, the results will be:
Poorly Blended
If you cut one parting with light tension and the next parting with heavy tension, the results will be:
Thumb
Palming the shares during haircutting reduces strain on the index finger and_____ while combing the hair
To ensure an even cut
In hair cutting, why is it necessary to always comb each parting from the scalp to the guide and remove all Tangles and distribute the hair evenly in The Parting?
Moisture
To ensure even results in the finished haircut, always maintain an even amount of ______in the hair
Thinning shear
The Implement mainly used to remove bulk from the hair is known as:
Clipper
Implement used to create very short tapers quickly is the:
Edger
What Implement is used to create clean lines around the perimeter of a short taper?
Fringe
The Triangular section of hair that begins at the Apex and into the front Corners is known as the:
Casting
The method of manufacturing shears whereby molten steel is poured into a mold and cooled is called:
Palming the shear
When the scissor is held with the ring and Little Fingers of the opposite hand while the hair is combed, it is called:
Four Section parting
When the hair is parted from the center of the forehead to the center of the nape and then parted from the crown down to the ears, it is known as:
Sectioning
What is necessary to help control the hair and produce a more uniform cut?
Growth pattern
The direction in which the hair grows from the scalp is called the______.
Density
The_______ of the hair will determine the size of the subsection when cutting.
Elevation
The angle or degree at which a subsection of hair is held or elevated from the head when cutting is called.
Exterior guide
The guide that creates two lines seen around the perimeter of the cut is called the:
Interior guide
When hair is layered and a high elevation, what Guide has used?
Travel guide
A guide that is directed to the next parting to be cut is called a:
An uneven cut
What will result if the head is not held in a consistent position when cutting the back and side sections?
Partings
Always take consistent and clean______ to insure an even amount of hair in each subsection and produce more precise results.
Apex
The highest point of the head is known as the____
Low elevation
Zero degree elevation cut is also known as:
High elevation
A 90-degree elevation cut is also known as
Long layered haircut
180 degree elevation cut is also known as
Parietal ridge
The widest area of the head, starting at the temples and ending at the bottom of the crown, is known as the?
Combed straight down and cut parallel to the floor
When cutting a zero degree, low elevation or blunt cut the hair is
90 degrees
When cutting a high-elevation cut the hair is held at______ from the head and cut to the desired length
The same length
Upon completion of the high elevation cut the hair should be_____when measured.
Partings opposite to those used when cutting
What type of parting or subsections are used when checking a haircut?
Crown
The area of the head between the Apex and the back of the parietal ridge is known as the____
Cutting line
The angle at which the fingers are held when cutting the line that creates the end shape is known as the________
Slide cutting
Method of cutting or thinning the hair using razor sharp shears is____
Remove bulk not weight
The main purpose of thinning the hair is to:
Razor
A versatile tool which is used to create a softline when cutting is the:
Keep the hair damp
When cutting with a razor it is essential to:
Overdirection
When you comb the hair away from its natural falling position rather than straight out from the head toward a guideline it is called_______
Tension
The amount of pressure applied when combing and holding a subsection is called.
Palm-to-palm
Cutting____ means that the palm of both hands are facing each other while cutting.
Releasing weight
Layers create movement and volume in the hair by_____
Texturizing
The process of removing excess bulk without shortening the length is called____
Comb
When removing length from facial hair, the_____is used to control the hair.